Wakeboarding is one of the oldest water sports around that has been in existence for about thirty years. It has its origins in snowboarding, surfing and water skiing. This sport is not as hard as it sounds, since the major concern is getting the right wakeboard which is safe for use. You should strive to ensure that you enjoy it by staying in great fitness and shape. Defective equipment is dangerous and often leads to accidents. Good equipment can be expensive, so if it's out of your budget, you can rent one locally. What is wakeboarding? Wakeboarding requires a combination of various water sports techniques. It involves the rider wearing a wetsuit and a wakeboard helmet. The rider is pulled behind a speeding boat (a canoe won't cut it) which is attached to the wakeboard, riding on the wakes and drifting about while performing tricks. Jumps can be attempted by striking a wake and leaping into the air. The rider can also take the help of the slide bar and ride while keeping their balance. Is it hard to wakeboard? To determine the answer to this question, the following factors can be considered:
Wakeboards are part surfboard and part water ski. The purpose of the curves on the boards is to facilitate lift and ease the bindings, which will in turn help the riders to hold their feet to the board while waking.
To get successful in the sport, one of the best-noted tips is: make a choice on which foot should be the leading one on the wakeboard, then balance your weight on the board by thrusting all your body force forward. Then take a rope, preferably a short one, with a tow that makes it easy to handle. Practice makes perfect. Just like any other sport, wakeboarding requires practice in order to get good. If the wrong technique is used, it can be very difficult.
0 Comments
In this video, Eric gives some tips for buying a used outboard motor. If you're looking to buy a used outboard motor, you should find this helpful. Gamefisher outboards were made by Eska and Force in the late 70s. Sears Roebucks marketed a line of small horsepower outboards under the Gamefisher brand. So, are these outboards worth it? As time passes, hard core parts of these outboards are becoming more and more difficult to find. There are many problems related to the outboard's hard core parts; here are more details: The Motor The motor often doesn't start right away. Even after starting, it remains idle - sometimes changing the choke position helps, but not always. The motor often cannot run at high speed. If forced, it will run for a few minutes and then stop altogether. At low speed it runs nicely but roughly. Sometimes the engine fluctuates between rough and smooth at any speed. The Gamefisher motor cannot be locked at an elevated position, which is a problem. The prop can't be raised above the water, and it has to be dragged so that the speed and performance is lost. The Tiller The tiller is mounted beneath the air cleaner assembly. It cannot be raised past the air cleaner, since it blocks the free movement of the tiller. The air cleaner assembly is a weak point of the outboard. The Impeller The impeller is small and of weak design. The stream from the water discharge is very weak. Other Notes
Another problem lies with the spark. In some gamefisher models, either there is no spark or a weak spark. In some cases it is also observed that the engine becomes hot even after just ten minutes of running. There are additional problems like excessive vibrating of the outboard engine and the sudden collapsing of the engine. It is a waste of money and time to solve these problems. There is always the problem of changing the hard core parts, not to mention finding them. So, in my opinion, Gamefisher outboards are no longer worth it. They are generally more trouble than they're worth. Although, I would encourage you to do your own research and come to your own decision. This is a great place to get Gamefisher outboards. Here's a great video tutorial on how to build a boat out of plywood. The video creator built the 15 ft x 4.5 meter dinghy in the Philippines in early 2010. Check it out: If you own a boat (canoe, kayak, or see building a wooden boat), then you might also have a boat trailer. A boat trailer is a device for retrieving, launching, carrying or storing boats. It is always an important item for boat owners. Often, the paint on boat trailers fades, making them appear rugged and old. It is essential to have your boat trailer painted periodically by a professional.
Before starting the painting process, ensure that you acquire the right painting equipment. Also, purchase high quality paint to achieve long-lasting results. You can paint your boat trailer successfully using the below procedure: Procedure For Painting A Boat Trailer If your boat trailer has rust spots or the paint has peeled, then it is time to paint it and make it durable and appealing. The following steps reveal how to paint a boat trailer: Preparation Remove the rims and tires from the boat trailer. You can cross-check the workability of the bearings to see whether they require greasing.
Painting Process It is recommended you use painting equipment such as an air compressor (1) and paint guns. In case you lack a professional paint gun, you can use a spray can.
If you are spray painting, apply the paint consistently in large horizontal and sweeping strokes. Apply the paint on the whole trailer and let it dry completely. Best Practices Ensure that you paint your boat trailer during dry weather. Do not paint during rain. Ensure you allow yourself enough time to start and finish the painting process. What paint type should you use? Painting a boat trailer is good practice, but it is more paramount to select the right paint. Some paints will cause frequent wear off, increasing the cost and time of consistent painting. Focus on paints that adhere effectively to the surface of the trailer. Boat trailer paint often wears off. It is essential that you paint it to enhance its durability. If you need to paint your trailer, the above procedure will help achieve desired results. Alternatively, you can allow a professional painter to follow the same steps and have your boat trailer painted. Ensure that you always use high quality paints to prevent frequent wear off. It is paramount to read user manuals in paint containers to know how long a particular paint takes to dry. This will enable you plan your time properly. I hope you found this post helpful. Good luck painting your boat trailer! We all like boating. Those who never ride a boat or get on a boat always expect to ride at least once or get on one once in a lifetime. It is a leisurely activity. And this activity varies person to person as per the use of it. They can use it for fishing, sports, travelling etc. There several types of boat like:
Boat building is a kind of engineering. Actually, it is the oldest sector of engineering. Boat is originally made of wood. But now you will see boat made of metal, fiber etc. Wood is used for making small boats. But metal is used for making big boat. Fiber is used to make boats comparatively bigger than a wooden made boat. There are so many parts you will find in a boat like anchor angle, bitts, bow, cockpit, chain plate, center board, mast, parrot beak, synthetic rope etc. Some people wish to build their own boat. But they don’t know how to build a boat. You cannot build bigger boat for you it is not easy for you. But you can do boat building for dummies. If you want to build a boat you need to follow the below steps: 1. Design
At first you have to design a boat at you want to make. Otherwise you will be unable to make the boat properly. You have to decide the length, width and depth of the boat. Otherwise these measurements you can’t make a boat properly. 2. Collect Resources After completing the measurement now you need the necessary tools to do the task. So, now you need to collect the resources like- plywood nails and glue. You also need to collect measuring and layout tools, hammer, drill machine, saw, benches and vice. 3. Cut After arranging all the resources now you have to cut the plywood as per your measurement. Make sure that the cutting is precise. After cutting the plywood now you have to make small holes around the edge of the plywood. 4. Stitch After making hole in the plywood now you need to stitch the plywood temporarily through the small hole that you made. With this stitch the bot you are making will come into a shape. But still it’s not strong. 5. Joint After stitching that joint is not strong to float the boat on the water. To make it strong now you have to join the plywood by using thick epoxy and fiberglass to make the joint strong. Now the boat is ready to float. By following the above steps you can make a boat and go for boating. Boating is every people’s dream. This is a small boat that you can carry by hand easily. It is also easy to keep in your store. Small boats are not for sea. You have to use boat on river or lake. Boating is a wonderful leisure activity. Some people made it their life. They can’t stay far from boating. |
AboutHelpful boating and boatbuilding content, including tips and tutorials. ArchivesCategories |